Local Electrician | Broward, Palm Beach, Orange County and Seminole Counties

KITCHEN REMODEL AS PER PLANS

1)——Remove 3 (Tankless water heater)40 amp 240 volt circuits from existing indoor circuit panel and relocate all circuits into new indoor circuit panel. 2)——Remove 2 (Pool heater)50 amp 240 volt circuits from existing indoor circuit panel and relocate all circuits into new indoor circuit panel.

1)——Install #4 gauge copper equipment bonding wire from pool fence back to pool equipment.

Replace (1) run dual capacitor for Condenser

Replace (1) dimmer switch

1)——Install customer supplied dimmer in kitchen.

1)——Extend circuit in garage from existing switch box using wire mold to desired location of outlet close to water heater. 2)——Install wire mold junction box with outlet and cover plate close to water heater. 3)——Remove 3 outdoor outlets and cover plates. 4)——Install 3 new weather resistant outlets and bubble covers at all locations. 5)——Caulk at each location to ensure weather proofing.

Perform Rcc

Replace (1) blower motor under warranty

1)——Went through affected circuits and found incorrect voltage at all points. 2)——Checked panel and found several loose connections including a burnt neutral from being loose. 3)——Tightened all loose connections and repaired loose neutral.

Diagnosis main breaker getting too hot and tripped Found: overloaded main breaker because total loads is approximately 320 amps while main service is capable of 200 amps. Recommend: relocate pool heater circuits ( two 50 amps circuits) by adding outdoor 100 amps sub-panel

1)——Remove and replace 100 amp main breaker. NOTE: Customer is aware that this may or may not fix half power related issue. FPL will be the next step for repair if issues continue.

Repairs according to the inspection report: 1. Repipe electrical pipes at the corridor next to the pool, pool equipment room and underneath the stair. Approximately 40ft on the wall and 30 ft underground. 2. Remove (2) empty junction boxes and conduit in pool equipment room 4. Install (5) screws of main panel cover in meter room 5. Install (1) cover for timer in meter room 8. Identify and label all condenser disconnect boxes 9. Replace (5) broken low voltage conduits of AC condenser units Permit fee will be passed through customer if needed Note: Work in pool equipment needs to hold until the roof done. We warranty all work done base on inspection report.

Supply and install new Rheem 3.0 ton AC Split system Supply and install hurricane tie down straps on outside unit Supply and install (1) new smart thermostat 10 year manufacturer's warranty on unit 1 year AC maintenance program on unit 1 year labor warranty on unit *NOTE* Only rheem unit will fit in existing location of air handler in closet. Existing unit is 17.5 in wide. Same as rheem

Replace (1) dual 80/5 mfd run capacitor Replace (1) 50 amps fuse

Outlet not working

AC replacement

Fixed scuttle hole Performed 2nd visit

Re-wire existing kitchen / dining / foyer / bathroom / laundry room. Remove all wiring from walls and trusses being removed / altered. Provide new circuits from the existing electrical panel to kitchen appliances as required. Re-locate existing wiring in kitchen / bath / foyer / laundry room as needed. Provide wiring to kitchen island (concrete cutting / patching by others). Supply and install recessed LED lighting fixtures as per plans.

Extend (1) 120v circuit to new outlet from existing outlet. Approximately 5ft

Basic maintenance

Dig about 1 ft underground around broken conduit area. Use Schedule 80 PVC to wrap around the rusty area, tight with stainless clamps then seal with exterior sealer to protect wires. Supply and install (1) U strap to secure the conduit to the wall

1)——Replace 20 amp breaker. 2)——Replace 30 amp 4 prong twist lock plughead.

1)——Supply and install 15 amp GFI breaker.

1)——Install new 25 amp breaker for hot water heater.