Local Electrician | Broward, Palm Beach, Orange County and Seminole Counties

1)——Remove 150 amp CHALLENGER BRAND meter/main breaker panel. 2)——Install new 150 amp CUTLER HAMMER or SIEMENS BRAND meter/main combo. 3)——UPDATE GROUNDING; Install 2 new ground rods, 1 water pipe ground and 1 low voltage ground bridge interconnected with #4 gauge bare copper wire.

Remove and replace (1) burnout meter can by 200 amp meter can Remove and replace (1) 150 amp outdoor panel by 8/16 circuits 150 amp main breaker panel Upgrade grounding system with (2) ground rods and ground bridge, #4 copper ground interconnected with ground rods and water pipe for safety Rough patch and clean area. Arrange emergency disconnect from FPL. Pull permit and get inspection.

1)——Run dedicated 20 amp circuit from outdoor main breaker panel to right below panel. 2)——Install 2 gang weather proof junction box with a GFI outlet and a standard outlet and a weather proof bubble cover. 3)——Remove outdoor outlet and bubble cover. 4)——Install new weather resistant outlet and bubble cover. 5)——Remove garage GFI outlet and replace with new GFI outlet.

This Job will be done in Stages. Stage 1: Disconnect all power to existing walk-in cooler/freezer. Cap off wiring to insure safety for employer Remove existing breakers out of panel to make room for temp power breakers Clean area. Stage 2: Install (2) dedicated 30A Circuits for temporary trailers. Install (2) twist lock 30A Outlets for above trailers on exterior of building. ***NOTE*** Power cord and twist lock cap for cord to be provided by others*** Stage 3: Remove temporary power circuit and outlets that were installed for temporary trailers. Connect new walk-in cooler/freezer to existing electric. Clean Area. Permit Fee : $1500.00 Permit will need Load calcs. Panel Schedules. Riser diagram.

1)——Remove 100 watt pool light transformer. 2)——Supply and Install 300 watt pool light transformer.

Replace plastic cover

Upgrade main electrical service from 200-amps to 400-amps as required by the building department. Add a second 200-amp electrical panel inside the garage. Add a 200-amp feeder from the new service to the new panel in the garage through the attic space. Upgrade grounding to current code. Coordinate FPL disconnect / reconnect of electrical service. Includes all inspections required by t he building department. Permit fees are already paid for.

1)——Go through circuit and check for loose connections, shorts, and bad devices. 2)——Tighten any loose connections, replace devices that are deemed necessary to be replaced and fix minor shorts. NOTE; Repair does not include line replacement.

1)——Remove and replace guest bath gfi outlet.

1)——Replace 8ft 2 bulb T12 fluorescent ballast.

Replace (1) dual capacitor 40/5

Replace (1) 240 sprinkler timer

Centralab Electric misc Replace (2) Fluorescent fixtures by LED ones

Double tapping was removed. Had new tankless double tapped with main feed. Blank covers were installed on top two breaker spaces

1)——Hard wire and install double oven.

Install (1) 72 inches 8 blades ceiling fan customer supplied in patio Install (1) exhaust fan customer supplied Disconnect existing ceiling fixture in bathroom and connect to vanity fixture to free up switch circuit for new exhaust fan Rewire switch box for outdoor security lights and patio ceiling fans

Warranty bad breaker

1)——Remove and replace 4 bulb T8 fluorescent ballast.

Replace (1) 200 amp indoor panel with 30/60 circuits 200 amp indoor panel Drop existing 6/3 Romex circuit for new double oven to new panel Hook up double oven and cook top Permit fee passed through customer if requested

1)——Remove 2 sconce lights at front of home. 2)——Supply and install 2 brass finished sconce lights at front of home. 3)——Remove 1 light fixture at side of home. 4)——Supply and install matching fixture on side of home to those in back of home.

1)Install 8 circuit 60 amp sub-panel next to existing indoor circuit panel and connect to indoor panel. 2)Extend 4 15 or 20 amp circuits into sub panel to free up 2 spaces for 60 amp breaker feeding sub-panel. 3)Bring existing double oven line into new sub panel and connect to 40 amp breaker.

Replace (1) blower motor under warranty Diagnosis level 1: one outlet is not working. Including breaker, outlet replacement. Not including run new wires if they are interrupted inside the conduit

Re-pipe clogged drain line from unit to condensate pump Vacuum water out of the drain underneath air handler Test the condensate pump to make sure it works properly Reseal air handler panels with foil tape and mastic

Troubleshoot / diagnose issue with second floor AC system not cooling. Checked condensate drain system, all working fine. System very low on refrigerant causing coil in air handler to freeze up and drip water upon melting if ice.

1)——Remove outdoor CHALLENGER 200 amp main breaker circuit panel. 2)——Install new GE 200 amp 8/16 circuit main breaker circuit panel. 3)——Label panel and clean area.