Local Electrician | Broward, Palm Beach, Orange County and Seminole Counties

Replace (1) 2.5 ton AC split system with high efficiency Rheem 16 seer system

Replace (1) burnt out outlet Replace (2) decora switches Check fan making noise

AC check up

Clean drain pipes and re-support it

To help prevent mold and mildew build up inside the air handler. We recommend install the UV light kit inside the air handler to improve air quality in your house Supply and install (1) hard start kit to help compressor start and run easier 50% of the cost will be deducted toward compressor replacement if compressor break down within 6 months Diagnosis level 1

Replace (1) run 70 mfd capacitor

1)——Remove existing security light. 2)——Supply and install double flood LED motion detected security light.

1)——Remove 2 motion detected 2 head security lights. 2)——Supply and install 2 motion detected LED 2 head security lights.

Diagnose / troubleshoot electrical issue with master bedroom Replace existing 2.5 Ton Split AC System with new high efficiency system

1)——Troubleshoot affected circuit to find solution as to why there is no power. 2)——As of now at the minimum the breaker needs to be replaced and at least 2 outlets need to be secured. 3)——Also 1-3 outlets may need to be replaced to be determined upon Troublehsoot.

WATER HEATER- 1)——Found correct voltage at water heater. 2)——Found a little bit of rust in water heater junction box but no evidence of water penetrating junction box from exterior elements which means moisture or water must be coming from water heater itself. 3)——The Water heater has the right voltage which means the electric to the water heater is good and there must be an internal issue with the water heater malfunctioning. DOUBLE OVEN/COOK TOP- 1)——Install and hardwire double oven. 2)——Install and hardwire cook top.

1)——Run dedicated 30 amp circuit from outdoor main breaker panel to right below panel. 2)——Install 30 amp twist lock generator rated inlet. 3)——Supply and install generator safety lockout clip. 4)——Supply and assemble 25 ft generator cord with 30 amp twist lock female and male adapters. 5)——Test run generator and instruct customer on how to operate.

Hello! Thank you for choosing Kings Electric & A/C for your Electrical upgrades and savings. I was called out this morning because you’re having issues with (2) fluorescent wrap light ballast. I gave you (4) options how this can be fixed and save you money as well in the future and on your electrical maintenance bill. If you have any question on the options I have given you, please reach out and we’ll be happy to explain them. Thank you for everything once again. Your electrical technician, Xavier

1)——ELECTRICAL INSPECTION: Go through all HIHATS and check to see if wiring was done correctly. 2)——Install 2 customer supplied HIHATS at existing lighting locations in hallway. 3)——Supply and install 30/20 quad breaker at circuit panel to free up space for arc fault breakers to be installed on circuits to newly installed HIHATS. 4)——Supply and install 3 arc fault breakers for circuits with new HIHATS on them. 5)——Secure 10 junction boxes to trusses in attic to newly installed HIHATS. 6)——Install junction box at splice for living room HIHATS where existing dining room light used to be. 7)——Pull permit and get inspection; cost covers application and drawings of HIHAT work only. Any additional requirements by city will be billed to the customer.

Install (6) Hi Hats on outside panel (Customer Supplied) Install (4) Hi Hats in dining room (Customer Supplied) Install (2) Pendant lights in kitchen (Customer Supplied) Install (2) Additional Switch Legs.

1)——Remove outdoor 150 amp FEDERAL PACIFIC main breaker panel. 2)——Install new outdoor 150 amp SIEMENS 8/16 circuit main breaker feed thru panel. 3)——UPDATE GROUNDING; Install 2 new ground rods, 1 water pipe ground and 1 low voltage ground bridge interconnected with #4 gauge bare copper wire. 4)——Install whole home surge protector. 5)——Pull permit and get inspection.

1)——Remove and replace customer supplied switch.

Replace (2) T12 4ft ballasts Replace (1) T12 8ft ballast Replace (1) receptacle

Perform 1st AC maintenance

1)——Remove existing ceiling fan. 2)——Install new customer supplied ceiling fan.

Perform 1st visit

1)——Remove 200 amp outdoor main breaker panel and 50 amp main breaker disconnect. 2)——Install new 200 amp 8/16 circuit main breaker panel. 3)——Install new 50 amp main breaker disconnect. 4)——Remove existing low votage lighting time clock in back yard connected to transformer and make safe. 5)——Remove unsecured outlet and junction box in front of home and install new weather proof junction box with GFI outlet and bubble cover. 6)——Locate GFI outlet that operates patio outlet and replace. 7)——Replace back patio outlet and install new bubble cover. 8)——Remove GFI outlet and bubble cover close to front ground lights time clock and replace. 9)——Remove and replace jack and Jill bathroom GFI.

Disconnect copper lines and remove evaporator coils Clean evaporator coil outside with chemical and re-install, connect copper lines and recharge freon

1)——Remove 2 kitchen outlets. 2)——Supply and install 2 new 20 amp GFI outlets.

Inspection report: double tapping because no space in indoor panel Solution: Replace (1) 150 amps main lug indoor panel Supply and install (1) GFCI outlet and bubble cover Extend drain pipe off the exterior wall about 1 ft Permit fee will be passed through customer if requested