Sunrise FL Electrician & AC Repair

1)——Reconnect power to vivint doorbell. 2)——Install doorbell chime.

Diagnosis - 1 GFCI outlet not working - 1 outlet not holding the plug - (2) outlets in kitchen need to be secured

Replace (1) 120v hard wire and battery backup smoke detector

Replace (1) 2 pole 20A switch for sprinkler pump

Replace (1) 20 amps double pole breaker for water heater Replace (1) 50 amps double pole breaker for AC

1)——Remove outdoor 125 amp meter enclosure and FPL down pipe. 2)——Install new 125 amp meter enclosure with new 1 1/2 inch down pipe and new #2 gauge copper feeders. 3)——Remove outdoor 125 amp main breaker circuit panel. 4)——Install new outdoor 125 amp 12 circuit main breaker panel. 5)——Install whole home surge protector. 6)——UPDATE GROUNDING; Install 2 ground rods, 1 water pipe ground and 1 low voltage ground bridge interconnected with #4 gauge bare copper wire. 7)——Label panel and clean area.

1)——Remove outdoor 200 amp main breaker circuit panel. 2)——Install new outdoor 200 amp 8/16 circuit main breaker panel. 3)——UPDATE GROUNDING; Install 2 new ground rods, 1 water pipe ground and 1 low voltage ground bridge interconnected with #4 gauge bare copper wire. 4)——Label panel, rough patch and clean area.

1)——Remove back patio sconce light and outlet. 2)——Install new customer supplied sconce light. 3)——Install new customer supplied outlet and cover plate on back patio. 4)——Remove and replace customer supplied outlet and cover plate in living room.

Supply and install (4) single gang wall boxes and (4) 20 amps outlets

1)——Remove indoor 200 amp main lug circuit panel. 2)——Install new indoor 200 amp 20/40 circuit main lug panel. 3)——Label panel, rough patch and clean area. NOTE; NO GUARANTEE THAT THIS WILL FIX THE FLICKERING LIGHTS ISSUE.

BATHROOM- 1)——Remove 5 existing 3 inch recessed HIHATS and 1 dimmer. 2)——Supply and Install 5 6 inch round LED remodel cut in fixtures using existing electric and install new LED slide dimmer. VARIOUS ROOMS- 1)——Supply and install 3 outlets.

Install (1) vanity light fixture customer supplied

1)——Remove existing AC disconnect. 2)——Install new 60 amp non fusible pullout disconnect.

1)——Troublehsoot 3 track light heads to see if problem is the ballast or bulb. 2)——Remove 3 6 inch Metal halide bulb track light heads. 3)——Supply and install 3 similar 6 inch Metal halide bulb or standard track light heads with LED bulbs.

Customer noticing oil like substance outside near condenser

AH making noise

1)——Troublehsoot 3 track light heads to see if problem is the ballast or bulb. 2)——Remove 3 6 inch Metal halide track light heads. 3)——Supply and Install 3 new LED track light heads. 4)——Relocate 3 existing metal halide track light heads. NOTE: Exisitng metal halide fixtures have a 35 watt metal halide bulb which is rated at 3300 Lumens. There currently is not a LED bulb that emits 3300 lumens of light. Therefore a LED fixture is the only option and the cost is much more than a bulbed fixture. Although the cost is higher, they are much more economical in the sense of maintenance, life expectancy and use of electricity. No changing bulbs or ballasts, they last 10-20 years or longer and use about half the electricity.

Supply and install New 2.5 ton rheem split system Supply and install hurricane tie-down straps on outdoor condenser Supply and install safety switch on AH Supply and install new outdoor slab for condenser 10 year manufacturer warranty on all parts 1 year Labor warranty with KINGS 1 year AC Maintenance with KINGS

Replace old 15 year split AC system with new 4.0 ton, 15 SEER, high efficiency AC system.

1)——Run dedicated 60 amp circuit 140 ft from indoor main lug panel to air handler through 1 inch pvc conduit on outside of home to inside. We may have to cut holes in ceiling to fish wires. We will do rough patch but will not be responsible for final patch, popcorn or paint. 2)——Install 60 amp non fusible disconnect at air handler. 3)——Run power whip from disconnect to air handler and connect power. 4)——Replace old 15 year split AC system with new 4.0 ton, 16 SEER, high efficiency AC system.

Install (1) motion light Install one back to back outlet Install one outlet in garage for garage door Install one box and sconce light outside

Install (1) motion light Install one back to back outlet Install one outlet in garage for garage door Install one box and sconce light outside

Install (1) motion light Install one back to back outlet Install one outlet in garage for garage door Install one box and sconce light outside

Install (1) motion light Install one back to back outlet Install one outlet in garage for garage door Install one box and sconce light outside

Install (1) motion light Install one back to back outlet Install one outlet in garage for garage door Install one box and sconce light outside