Pompano Beach FL Electrician & AC Repair

MAIN LUG CIRCUIT PANEL- 1)——Remove 200 amp indoor main lug circuit panel. 2)——Replace with new 200 amp indoor 42 circuit main lug panel. 3)——Label,rough patch and clean. NOTE: The exsitng panel is to small and has no spaces left for the work needing to be done to bring kitchen up to code as we will need to add circuits and install 24 arc fault breakers in total to new circuits and exisitng to do so. DEDICATED CIRCUITS- 1)——Run dedicated 20 amp circuit from panel to microwave location. (Approximately 70ft) 2)——Run dedicated 20 amp circuit from panel to cooler location. (Approximately 70ft) 3)——Run dedicated 20 amp small appliance circuit from panel to 1 set of counter top outlets in kitchen. (Approximately 70ft) Code requires 2 small appliance circuits in kitchen, right now there is only 1. 4)——Run dedicated 40 amp cook top circuit from panel to cook top location. (Approximately 70ft) Cook top and oven are wired to same circuit that is not big enoug

Needs to vent exhaust fans (2) to eve

Diagnosis lights flickering Convert 1 light switch to GFCI outlet in kitchen Total cost will be credited toward new panel replacement

1)——Remove exsitng aluminum wiring and broken weather head from 2 inch riser. 2)——Install new customer supplied #3/0 gauge wire through 2 inch riser and connect to meter enclosure. 3)——Install new 2 inch weather head. 4)——Remove 3 defective lugs and bad meter jaw. 5)——Install 3 new meter lugs and 1 new meter jaw. 6)——Pull permit and get inspection.

After the Fact permit for kitchen remodeled without a permit. Submit to the building department permit applications and secure inspections for the work done by previous owner. All code violations, permit fees and possible repairs are not included in this estimate. Drawings, engineering or fees incurred by the City of Pompano Beach are not included in this estimate.

Install (1) GFCI outlet with bubble cover

1)——Remove 125 amp indoor main lug circuit panel. 2)—-Install new 125 amp indoor 20/40 circuit main lug panel. 3)—-Install whole home surge protector. 4)—-Label, rough patch and clean.

Perform red carpet club AC maintenance Change filters Check Freon pressure Flush drain line

Perform red carpet club AC maintenance Change filters Check Freon pressure Flush drain line

Perform red carpet club AC maintenance Change filters Check Freon pressure Flush drain line

Perform red carpet club AC visit Change filters Check Freon pressure Flush and level drain line

Replace (1) 2 gang outlet/switch for outdoor fountain Replace (1) landscape lights transformer customer supplied

Extend closet light circuit be cut when we re-do pool pump electrical circuit

Remove existing rusted junction box of pool pump Run new conduit from outdoor panel to new location where the switch will be installed for pool pump Install (1) 60 amps sub-panel next to outdoor main panel to feed pool pump and future use Redo AC whip, tight all connectors with locknut Relocate (1) 240v 30 amp circuit to new sub panel Pool pump defective is customer responsibility

AC service

1)-----Remove ballast at 1 parking lot pole light and wire fixture to line voltage. 2)-----Supply and install 400 watt equivalent LED bulb. NOTE: THERE WILL BE ADDITIONAL CHARGES FOR BUCKET TRUCK.

Replace (1) outlet Install (1) box

1)——Disocnnect photocells at building lights location and yard lights location. 2)——Run dedicated 20 amp 2 pole circuit to location of new timer to be installed approximately 2 ft of wiring. 3)——Install 20 2 pole timer. 4)——Connect switch line from yard lights to new timer. 5)——Run switch line from new timer to exsitng switch line junction box feeding building lights. (Approximately 50ft)

Service replacement Supply and install new indoor 200amp panel Supply and install new 200amp outdoor panel Update grounding system Pull permit

1)——Remove existing electric to well pump junction box. 2)——Install new weather proof box with 240 volt 30 amp switch and in use bubble cover.

1)----Install 220 volt 20 amp outlet with industrial cover plate in exisitng junction with existing wiring.(unit 41)

AC replacement

1)----Disassemble kitchen fan. 2)----Remove remote transmitter and wire fan directly to switch line. 3)----Reassemble and install fan.

Replace existing 4.0 Ton split AC system with new 4.0 Ton high efficiency AC split system.

Make repairs above. Diagnosis tripping breaker