Coconut Creek FL Electrician & AC Repair

Hey Michele! Thank your choosing kings electric & a/c for your electrical upgrades. Today we were able to finish the work with your main disconnect on the side of your house. We added a new whole home surge protector, and the interlock for your generator breaker. If you have any questions or concerns, please reach out. Have a great Day! Your electrical technician, Xavier

1)——Pull 20 amp 240 volt dedicated circuit through existing conduit to existing junction box approximately 40ft. 2)——Extend circuit from existing junction box less than 5ft and install new junction box with 20 amp 240 volt outlet and cover plate.

1)——Install 4 new dedicated 20 amp circuits using emt conduit from indoor panel to existing junction box.(Approximately 30ft) 2)——Route first 2 circuits through existing conduit to floor box and extend circuit from floor box using emt to desired location of quad outlets to be installed. 3)——Install quad outlet at first location. 4)——Route second 2 circuits through existing conduit to other junction box on wall and then down to floor box. 5)——Extend circuits from second floor box to desired location of quad outlets to be installed. 6)——Install quad outlet at second location. 7)——Label circuits at panel and junction boxes.

1)——Remove GFI in office and install duplex decora outlet. 2)——Wire existing fan switch to black wire switch leg. 3)——Fasten 3 existing outlets onto wall.

1)——Run dedicated 20 amp circuits to disposal, fridge and small appliance. 2)——Fix flying splices in wall and secure all wire properly in a junction box. 3)——Reinstall all outlets and switches properly and make sure all are working properly. 4)——Install/add fridge outlet.

1)——Replace garage door 15amp breaker.

1)——Remove existing exhaust fan in downstairs bedroom/bathroom. 2)——Supply and install ductless exhaust fan to existing electric.

Supply and install new fan motor. Supply and install new capacitor

1)——Remove fluorescent fixture in kitchen. 2)——Extend existing switch line of fixture removed to 4 locations. 3)——Supply and install 4 6 inch round LED remodel cut in fixtures in kitchen. 4)——Run switch line from existing switch box 2 4 locations in living room. 5)——Supply and Install 4 6 inch round LED remodel cut in fixtures in living room. NOTE: Rough patch included if needed.

Raise Drip Loop off of roof in order to meet code. Install new Updated grounding system up to code.

Remove cloth wiring in attic. Install (3) Junction Boxes in attic for open splices. Remove timer off of thermostat Remove time clock wiring due to exposed romex.

1)——Install dedicated 20 amp circuit and junction box next to panel. 2)——Run 3 wire circuit from junction box to feed 2 separate switch leg locations where lights are to be installed. 3)——Install junction box at both locations. 4)——Install 2 customer supplied hi-bay LED lights. 5)——Install 2 customer supplied LED dimmers. 6)——Rewire fluorescent fixture to line voltage and install customer supplied LED bulbs. NOTE; CUSTOMER IS SUPPLYING LIFT

1)——Hang customer supplied security camera.

Replace (1) GFCI outlet in kitchen

1)——Troubleshoot and rewire fan. 2)——Remove 3 existing light fixtures. 3)——Supply and Install 3 LED 11 inch round flat panel light fixtures.

Supply and install (1) dimmer switch

Replace (1) 20 amps outlet for microwave Supply and replace (1) amps plug for microwave which is burnout

1)——Run switch line from existing switch box at both kids rooms to 4 locations in girls room and 3 locations in boys room. 2)——Install 4 6 inch round LED cut in fixtures in girls room and 3 in boys room. 3)——Install switch box and switch at both locations. 4)——Remove and replace customer supplied vanity lights at 2 guest bathrooms. 5)——Install 2 6 inch round LED Pho-HIHATS.

Low Freon Vacuum AC drain line

1 year AC red carpet club Replace (1) 240 condensate pump

1)——Remove dimmer in family room and install standard toggle switch. 2)——Remove standard toggle switch at master bath vanity light and install dimmer from family room at same location. 3)——Remove existing vanity light in master bathroom and modify new light so that it may be centered and install new customer supplied vanity light. 4)——Remove and replace customer supplied guest bedroom fan.

1)——Run 100 amp circuit from existing power source using 1 1/4 inch emt conduit and metal flex with #2 gauge copper wire to machine location. (Approximately 50ft) 2)——Install 100 amp disconnect and hardwire machine into disconnect.

Make T valve for 2 AC drain lines in order to flush from inside and future maintenance

Hook up GFCI outlet in kitchen

1)——Remove 4 outdoor outlets and and cover plates. 2)——Install 3 weather resistant outlet and 1 weather resistant GFI with bubble covers at each outdoor location. 3)——Remove 1 indoor GFI in garage and replace with new weather resistant GFI. 4)——Remove back patio spot lighting system. 5)——Install proper extension at exsitng outdoor outlet to extend circuit. 6)——Run conduit from extension ring to switch location and install weather proof switch box. 7)——Run switch line to 2 desired locations of spot lights to be installed. (Approximately 30ft) 8)—-Install weather resistant outlet and bubble cover at extension ring. 9)——Install weather proof box at each location of spot light. 10)—-Supply and install 2 double flood switch only operated LED fixtures. 11)—-Run switch line in three bedrooms for new lighting systems. 12)—Supply and install 4 6 inch round LED remodel fixtures in 3 bedrooms for a total of 12. 13)—Supply and install 3 LED rat