Local Electrician | Broward, Palm Beach, Orange County and Seminole Counties

1)-----Remove exsitng 80 amp panel that is currently double tapped at meter enclosure. 2)-----Install junction box at exsitng circuits conduit that was connected to sub panel. 3)-----Remove single lugs at meter enclosure and install double lugs. 4)-----Install 100 amp disconnect next to meter enclosure. 5)-----Install new 3 gauge copper feeders between meter and new disconnect. 6)-----Run 1 1/4" PVC conduit from disconnect around house to back patio. (Approximately 100 ft.) 7)-----Install 100 amp 12-24 circuit outdoor panel at back patio. 8)-----Pull 3 gauge copper feeders from disconnect to patio panel. 9)-----Install 50 amp GFI breaker at new panel on patio. 10)-----Run 1 inch PVC conduit from patio panel to hot tub location. 11)-----Run flex into hot tub motor and hook up hot tub. 12)-----Relocate new outlet for water softener into outdoor main breaker panel.

1)-----Assemble and install 2 customer supplied fans.

Main breaker is off Turn on and check everything Make sure they are working

Install customer supplied motion light

Install new 4 prong outlet

Diagnose intermittent power at ac wall unit

1)-----Install customer supplied emergency light.

Replace (2) emergency ballasts

Replace (1) 6 lamps fluorescent fixture Replace (1) 6 lamps fluorescent fixture

1)-----Remove all wiring and junction boxes from half wall. 2)-----Cut conduit that has all circuits main feeds down to desired location of outlet to be installed. 3)-----Install deep junction box in wall at main feed conduit. 4)-----Extend circuit from main feed junction box to exisitng outlet junction box on opposite side of wall. 5)-----Install outlet and cover plate at both junction boxes. 6)-----Trace out both fan switches and reconfigire wiring so that they operate on 1 switch line. (Preferably 1 switch, but might have to be 2 switches on a 3 way system)

1)-----Remove bathroom vanity light fixture. 2)-----Cut off bad wire to exisitng switch line of bathroom light fixture junction box and pull slack of exisitng good wire back into junction. 3)-----Pull slack of 3 other lines to other side of stud and cut bad wire off those 3 lines. 4)-----Install junction box in wall and reconnect all lines. 5)-----Extend feed to bathroom light junction box from newly installed junction box. 6)-----Reinstall bathroom light fixture.

Replace (2) GFI outlets

1)-----Schedule disconnect with FPL. 2)-----Remove 200 amp meter enclosure. 3)-----Install new 200 amp meter enclosure. 4)-----Remove 200 amp main lug outdoor circuit panel. 5)-----Install new 200 amp main breaker 20/40 circuit outdoor panel. 6)-----Label panel. 7)------Install new 2/0 gauge copper feeders between meter and main panel. 8)-----Remove aluminum feeders between main outdoor panel and indoor circuit panel. 9)-----Install new #2 gauge copper feeder wires between main outdoor panel and indoor circuit panel. (Approximately 3*70 ft.) 10)-----UPDATE GROUNDING INCLUDES: install 2 new ground rods, 1 water pipe ground and 1 low voltage ground bridge all interconnected with #4 gauge bare copper wire. 11)-----Pull permit and get inspection.

1.....replace old surge protector 2.....install one new dbl pole breaker for new surge protector to correct double tapping.

Replace (1) capacitor and (1) contactor Add 3-6 lbs R22

1)-----Reinstall customer supplied generator transfer panel. 2)-----Pull exisitng wires of circuits connected to transfer panel through exisitng conduit to house panel. 3)-----Reconnect all circuits to house panel as labeled. 4)-----Reinstall generator outlet. 5)-----Supply and install 100 amp breaker in house panel and connect power supply wires from transfer panel to house panel.

Replace bathroom gfi outlet

Wire up (4) cubicle wiring 1 year warranty

Troubleshoot no power

Replace breaker

Install customer supplied 350lb chandelier

1)-----Remove burnt 100 amp main breaker and meter socket. 2)-----Supply and install new 100 amp main breaker and meter socket. NOTE: Meter socket is special order.

Diagnostic on outside outlet

Remove circuit out of panel

Supply and install new 20amp 2p breaker for sprinkler in order to avoid double tapping